How to build an easy DIY shoe rack

Any entrance can quickly become a dangerous mess of discarded shoes, ready to stumble anyone who enters your home. You may know in your heart that the solution to this inhospitable problem is a shoe rack, but you may not know how easy it is to make.

There are also advantages to building one from scratch: not only will you be able to personalize the project to suit your style and decor, but you can also save money. Although the price for a low-quality shoe rack, which is required for assembly, can exceed $ 100, I managed to assemble this rustic hardwood table for about $ 60. If you already have some of these supplies on hand, you may be able to make your own for even less.

Warning: DIY projects can be dangerous, even for the most experienced makers. Before proceeding with this or any other project on our site, make sure you have all the necessary safety equipment and know how to use it properly. At a minimum, this may include goggles, a face mask and / or ear protection. If you use power tools, you must know how to use them safely and correctly. If you are not doing this or are otherwise embarrassed by anything described here, don’t try this project.

statistics

  • Time: 3 to 4 hours
  • Material price: $ 60
  • difficulty: Easy to moderate

Materials

Instructions

1. Prepare the wood for cutting. If you don’t have a special workshop, choose a space big enough for you to move around and make your cuts. Then, using a tape measure, pencil and square, mark the following cuts for each part of the table:

  • Table board: Draw a line halfway on one of your 2×6 pieces so that you will cut two boards of approximately 4 meters.
  • shoe rack: Mark the second 2-by-6 at 44.5 inches.
  • Legs: Mark each of the 2-x-4 at 29.5 inches from one end and 29.5 inches from the other end, for a total of four cuts. Focusing on the end of one of these legs that will soon be, mark a line in the middle of the plate, 2 inches from one of the long sides, and make another mark 5 inches down on the same side. Use your square to draw a diagonal line between them, giving the lower leg a slight taper. Repeat this on the other three legs.
  • Long side table cover: Mark one of the 1×4 boards at 44.5 inches from one end and 44.5 inches from the other end, for a total of two cuts.
  • Short side cover of the chair: Mark the other 1 by 4 by 10 inches from one end and 10 inches from the other.
  • Table holders: Mark the unmarked part of the second 1×4 so that you get three 8 ⅜ inch pieces. Spread them out a little to leave room for about ⅛ inches that the saw blade will shave.

Take advantage of this time and to remove all barcode labels and paper clips so you don’t have to deal with them when you paint the pieces later.

2. Cut the wood. Use a circular saw to cut each piece of wood you marked in step 2.

  • Pro type: For a perfect cut, align your circular saw blade with the pencil lines, then place the square in line with the left side of the circular saw shoe (a flat metal part that rests on wood) to guide the process.

3. Sand the wood. Using a piece of sandpaper, sand each piece of wood until it is smooth and brush to clean dust and debris.

  • Pro type: If you are worried about debris, wear gloves or wrap sandpaper around the wood to create a tampon for your hands.

4. Assemble the table leg set. Using a drill and screws, fasten the two legs together as follows:

  • Place the two legs (29.5-inch 2×4 pieces) so that their outer edges are 44.5 inches apart.
  • Place one of the 44.5-inch 1×4 trim between the legs so that it is flush with the top (uncut end) and the outer edge of each leg.
  • Screw four 1.5-inch screws into the wide 1-by-4 surface to connect it to the legs: two on each side, 2-by-4 in the middle, and 1 inch from the nearest edge. Make sure the head of each screw fits at least ⅛ inches into the wood. (In step 10, you will fill these holes with wood putty).
  • Repeat this step for the other set of legs.
When you are done assembling one set of legs, it should look like this. jose mendoza

5. Attach the short side trims. Stand one set of legs on its short side to make it easier for you to work on this step. Place one 10-inch piece of 1-x-4 along the outer leg that is off the ground and closest to you, so it looks like the long piece of ornament you used to connect the two legs rotates 90 degrees. Attach the short decorative piece in place with two 1.5-inch screws, each 1 inch from the nearest edge and centered on the leg below. Repeat this step on the other leg (you can see the result in the photo below step 6).

6. Put two sets of legs together. Place the set without the attached side cover on the ground and place the other on top. The two of them should fit together as pieces of a puzzle. Fasten them by drilling two 1.5-inch screws into the 10-inch side and 2 by 4, just as you did in the previous step. Repeat this on the other leg. Your table should now be able to stand on four legs, which means you’re almost done assembling.

A person assembling a wooden DIY shoe rack outside on a concrete driveway.
The pieces should fit perfectly (or close to it). Mary Kearl

7. Install the shoe rack. If you raised your table to test it, lay it back on its side and use a tape measure, square, and pencil to mark 6.5 inches from the bottom on all four sides of all four legs. Here you will attach the shoe rack.

Using a ¼ inch drill bit, make two ½ inches of deep holes on the 4-inch side of each foot. Each hole should be ¾ inches above the lines you just marked and 1 inch from the nearest edge.

Now place your 44.5-inch 2×6 between your legs, leaning on a stand that will soon be placed directly above the lines you drew. The lines should be visible just below the board. Finally, drill 2-inch screws into each of the pre-drilled holes. (In step 10, you will fill these holes with wood putty).

  • Pro type: Temporarily place the remaining 1×4 piece under the tapered end of each foot on the ground. This will match the 1-by-4 screws attached to the top of the legs and keep everything level while you work.

8. Install the table top. Straighten your desk. It only remains to assemble the upper part. Place your two boards of approximately 4 meters 2×6 on top of the table so that they touch approximately in the middle of the frame. It will rise on all sides. For a smooth finish, use an ¼ inch drill bit to drill one hole facing up on the inside of each foot closest to the longitudinal side of the table and directly below the table top. The hole should be centered and 1 inch from the top of the foot, and go into the table top about half an inch. Be careful not to pierce the top 2-x-6, put one 2-inch. twist into each pre-drilled hole, attach each leg to the board at the top.

A person drilling at an upward angle into a table top on a wooden DIY shoe rack.
This is the angle you are going to in step 8. jose mendoza

9. Install the table brackets. Take one of your 8 in-inch 1×4 pieces and place it under the table with two legs on one short side of the table. Screw it into the table top with two 1.5-inch screws, each 2 inches from the long side of the table and centered on 1-by-4.

Attach the other 8 ⅜ inch piece directly under the table top to the other two legs, attaching it in the same way. Then center the third 8 ⅜ inch piece between the two short sides and fasten it exactly as you placed the other two pieces.

Finally, strengthen the supports you just attached with the additional 1.5-inch screws on the outside (one per bracket on each longer side, a total of six screws). Tighten one screw directly into the center of each end of the three 1-by-4 from the outside through long pieces of trim.

10. Fill the holes with wood putty. Wipe off any residue around the screws and apply wood putty to each hole as needed.

  • Pro type: You can use a small piece of wood residue as an applicator to add putty if you want to keep your fingers clean and avoid possible debris.

11. Get ready to paint the chair. Sand the entire table, making sure each surface is smooth, and remove debris from the wood putty. Then use your brush to remove all the dust from the table.

  • Pro type: If you do not have a floor covering or any surface on which you are, you can use newspapers and coupons from the store to keep it clean.

13. Paint the table. Using a brush (make sure to remove dust), apply the color of natural wood to the table top, and then a solid color of your choice to the rest of the table. Allow both stain and paint to dry and apply a different coat for each.

  • Pro type: Put a piece of wood under each foot before you start painting – so your feet won’t stick to the paint cover.
  • Note: Make sure you follow the paint or stain manufacturer’s instructions and make sure you apply your coats in a well-ventilated area.

Now your hallway will be complete and without danger.

Leave a Comment